Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[..]

I realized that this it hasn't been discuss a lot before and funnily I've had a hard time finding one.

The closest I've ever found is Julia Roberts 5'8" and Eric Roberts supposedly only 5'9"



And while not equally interesting of a subject, the following are also worth mentioning and easier to find.

6'4 Chris and Liam Hemsworth and 5'9" Luke Hemsworth


6'5" Randy Quaid and 6' Dennis Quaid


5'4" Emilio Estevez, 5'9" Martin Sheen and 5'7" father Charlie Sheen


5'10" James Franco and 5'6" Dave Franco


6'3" Ben Affleck and 5'9" Casey Affleck

[cheekycabs]

How to replace a toilet or install a new one yourself. If you're installing a new toilet in a new location, you'll need to run (or have someone run) a water supply line and a drainpipe, which must be connected to the drain/vent system in compliance with code. Even if you're just replacing an existing toilet, you should replace the water supply tubing as well.



Skill Level: Beginner
Time: 2 hours

Step 1
Determine What Flange You'll Be Using
Determine What Flange You'll Be Using
If you're reusing the old flange, it's a good idea to replace the 3/16-inch flange bolts. Purchase two 3-1/2-inch-long closet bolts at your local home centre. If you're replacing the flange, it must be screwed into a wooden floor. Self-tapping concrete screws are used for concrete.
Step 2
Place Wax Ring on Toilet
Place Wax Ring on Toilet
Place the wax ring on the toilet. The "no-seep" wax ring size will vary with the size of the flange. Be sure to purchase the proper size. A 3-inch neck will fit a 3-inch closet elbow, and a 4-inch neck will fit a 4-inch closet elbow. If the closet elbow is 4 inches and the neck is 3 inches in diameter, purchase a 4x3 reducer.
Step 3
Set the Toilet Bowl
Set the Toilet Bowl
Straddle the toilet bowl and lift, using your legs and not your back. Toilets are heavy, so get some help. Set the toilet over the anchor bolts and sit on the toilet, rocking it back and forth to seat the wax ring.
Step 4
Tighten the Nuts
Tighten the Nuts
Draw the nuts down over both anchor bolts until they are hand-tight. Shim as necessary to maintain level. Use an adjustable wrench and — moving from one side of the toilet to the other-alternate the tightening of each nut a half-turn at a time until it's snug. Don't over tighten.
Step 5
Cut Flange Bolt to Size
Cut Flange Bolt to Size
Use a mini hacksaw to cut the flange bolt so only 1/4 to 1/2 inch extends above the bolt. This will allow the cap to fit snugly. Most bolts have snap-offs every 1/2 inch or so, but you should still cut through so you don't bend the bolt.


Step 6
Install the Bolt Cap
Install the Bolt Cap
Install the bolt cap. Some types of caps will snap over the bolt. Others have to be filled with plumber's putty and seated over the anchor bolt.
Step 7
Set the Tank Anchor Bolts
Set the Tank Anchor Bolts
Set the tank anchor bolts. Place the tank anchor bolts in the holes of the tank to help guide the tank onto the bowl.
Step 8
Place the Tank on the Bowl
Place the Tank on the Bowl
Lift the tank and place it over the bowl. You may need some help with this. Guide the tank bolts into the corresponding holes on the toilet bowl.
Step 9
Tighten the Tank Bolts
Tighten the Tank Bolts
Hold an adjustable wrench over the tank bolt nut while you tighten the bolt with a screwdriver. Don't over tighten; you can crack either the tank or the toilet bowl.


Step 10
Install the Shutoff Valve
Install the Shutoff Valve
Set the valve over the compression ring and draw the nut to it. Tighten the nut until hand-tight. Use two adjustable wrenches to tighten until snug — one to hold back the valve and the other to tighten the compression nut.
Step 11
Measure the Supply Tube
Measure the Supply Tube
Hold the tank supply tube so it's in place. Let the extra pipe extend past the shutoff valve. Mark the pipe for cutting. Leave enough pipe so it will fit snugly inside the shutoff valve outlet. Cut the supply pipe with a tubing cutter. If you think your plumbing skills are limited, you can use a braided supply line instead of the solid supply line shown above. Be sure your supply line and shutoff valve are compatible before leaving the store.
Step 12
Connect Supply Pipe to the Tank
Connect Supply Pipe to the Tank
Seat the end of the pipe against the tank. Draw up the tank nut. Hand-tighten until snug. Slide the compression nut over the other end, and then place the compression ring over the end of the pipe. Seat the end in the outlet of the shutoff valve.
Step 13
Tighten the Compression Nut
Tighten the Compression Nut
Use an adjustable wrench to carefully tighten the compression nut. Don't over tighten. Turn on the water supply and check for leaks along the supply line, visually and by touch. Flush the toilet and check for leaks around the base of the tank. If there is a leak, tighten the connections a half-turn.

[GrowTow]

It must really such to be Luke Hemsworth, easily has the best looking face but lacks 8 inches which nothing can make up for

[shottrue]

It says 5'11 for Luke Hemsworth but in photos it does look pretty crappy, it is a 5 inch difference which is basically half foot